MINI GENERATOR (With Light Switch) For Motorized Bikes

Description

Super Dynamo Lighting
Bicycles and Motorized Bikes...Avoid Accidents...Avoid Tickets...Get Lights!
Motorized Bicycle Lighting
6 Volt Mini-Generator
12 Volt Mini-Generator Max
6 Volt Mini-Generator With Switch
12 Volt Mini-Generator With Switch
6 Volt Mini-Gen for Pull Start Engines
12 Volt Mini-Gen Max for Pull Start Engines
Complete 6 Volt Lighting System LS-1
Complete 7.2 Volt Lighting System LS-2
Complete 12 Volt Lighting System LS-3
Enclosed Light Switch SPST
Enclosed Light Switch SPDT
Encased 6 Volt SLA Battery
Encased 7.2 Volts AA Battery Pack
Encased 14.4 Volts AA Battery Pack
6 Volt Mini-Charger For LS-1 and LS-2
12 Volt Mini-Charger for LS-3
Magneto Coil Mini Charger
Magneto Coil Lighting System
Heavy Duty Headlight Bracket
Heavy Duty Tail Light Bracket
MINI-GENERATOR With Light Switch For Motorized Bicycles
This is a Mini-Generator made to provide electricty for 6 volt lighting of about 3 to 5 watts. This item includes a SPDT Light Switch and is easily installed. Instructions for installation are included.
The second and third photos below illustrate the Mini-Gen installed into the engine's magneto housing. This "Mini-Gen" is a mini generator and will produce reliable electricity for all common 6v 3w headlight systems.
This generator will run lights of higher wattage, but for best all around performance, a 3 to 5 watt lighting system is recommended. Just install into magneto case using the 2 rear magneto screws, then route red (output) wire through wire harness. The red wire from the MINI GENERATOR will send electricity to your lights through a light switch or connected directly for continuous light.
For a more stable lighting system you can add a Mini-Charger and battery pack available in our store (links on left side).
NOTE:
Please feel free to inquire about pricing for any single item(s).
Install this mini-generator and get lights for your motorized bike.
No more troubles from dead batteries and flimsy lights.
A light switch is included for connection to lights.
The SPDT switch includes an optional ground wire for neutralizing the Mini-Gen when lights are off; resulting in smoother transaction.
Mount the switch on upper frame rail, handle bar or where ever you wish.
Note:
Mini-Gen wire is approx. 12" long and switch wires are approx. 6" long. No extra wire included.
Click on the links on the left to check out our other items.
Just remove the engine magneto cover, then use the 2 rear screws to attach Mini- Generator inside engine magneto case.
Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen wire into grommet.
Use a pick or small screwdriver or nail to push into the area where wire will fit, then insert wire.
Instructions and precautions are included for Mini-Gen installation.
After the Mini-Generator is installed, the power wire should be routed toward bicycle seat post for Mini-Charger connection, unless it's being used for other purpose.
Position wire inside case away from moving parts and also make sure it will not be pinched under the cover.
Use duct tape (any color) or cable ties to secure wire onto bike's bottom bracket and seat post.
The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger. Your results will look far better than this one.
Here is the Mini-Gen's voltage being measured.
The Mini Gen here is producing a little over 6 volts for all 6 volt lighting systems and accessories.
This is called a generator (which technically produces dc voltage), but this produces AC voltage.
The engine speed here is around 900 to 1000 RPM which is just a little above idle speed.
Most riders will produce this voltage at a slow speed of around 12 to 15 MPH.
Higher voltages of around 12 or more is obtainable at much higher engine speeds, but 6 volts is recommended for all around best performance.
The Mini-Gen is seen here hooked up to a common 6 volt / 3 watt bicycle headlight and tail light .
This type of lighting is rated at around 500 milliamps (1/2 AMP), but it was tested on a fully charged 6 volt battery and used about 0.435 amps (or 435 milliamps).
Here in the photo you see the light using 424 milliamps at just a little over idle speed.
Unlike most LED lights, regular light bulbs will run off both AC and DC voltage with no problem.
Caution:-
If running lights directly from Mini- Gen, avoid revving up the engine with lights on because high revs for more than 5 seconds can immediately blow the bulbs.
High speeds while driving is perfectly o.k.
Example of a 6 Volt Lighting System
A photo of a popular 6 volt / 3 watt bike lighting system is seen here.
This ad is for a Mini-Gen
only
and does not include lights.
Check out our other ads for Mini-Gens which include lights and other accessories.
Please note that some 6 volt light bulbs will perform better than others.
A 6 volt bulb of higher amperage or wattage rating does not necessarily shine brighter.
A common 3 watt bicycle dynamo type headlight and tail light are seen in this photo.
PAYMENTS
Payments for auction items are expected within 3 days, but no later than 7 days. All payments accepted through Paypal or CIP. Serious inquiries about payment for individual items welcome.
SHIPPING
Flat rate shipping & handling price is available for the continental USA. Shipping & handling might also be the same for other states outside the continental United States. This item will normally ship within 2 business days, but could take up to 5 business days. To check shipping and handling fees to your state just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
Items will be shipped to the address provided for transaction. Request to change shipping address after item is shipped will be ignored.
We reserve the right to refuse shipment to uncomfirmed addresses in which case buyer will be refunded.
INTERNATIONAL
shipment is available with slightly higher fees. To check shipping and handling fees to your country just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
WARRANTY & RETURNS
The SUPER DYNO Lighting System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If you are unsatisfied for any reason, just return the complete kit, and a refund will be issued (less shipping and handling). Shipping & handling is not refundable, and the customer is responsible for shipping cost of the returned item.If any problems are experienced with our products, please contact us for assistance before resorting to any other course of action.
NOTE- Any item showing signs of tampering or abuse will void warranty!
INTERNATIONAL
customers are legible for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping returned items.
DISCLAIMER
This "SUPER DYNO Lighting System", and all parts, pieces, ideas and designs associated therewith, are the proprietary rights and ownership of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are discouraged and expressly prohibited.
By purchasing this system you agree to abide by any and all traffic laws governing your city, state or country and further agree to hold Wonderful Creations and any associates thereof, blameless for any accidents, mishaps, property loss, damages, death, injuries or expenses reportedly, or supposedly caused by the use, or misuse of this lighting system.
Copyright © 2004-2010 Wonderful Creations . All rights reserved.